Archive for the ‘Shadow’ Category

I Knew It!

Thursday, November 2nd, 2006

These pictures, taken by Allen Shope and posted to the IPDB confirm my suspicions. Why? Why would you remove these helpless figurines from a machine? Why? For the love of humanity!

Mongol to the left of the left ramp.

Mongol at upper-right flipper.

All drama aside though, you can see in the two pictures above that my Shadow is indeed missing a Mongol figurine just to the left of the left ramp, and missing another over by the upper-right flipper.

You can also see from the picture on the left that the machine should have a small plastic cover over the left ramp entrance. The picture below shows the one that goes over the right ramp:

Missing plastic over right ramp.

Parts Arrival

Thursday, November 2nd, 2006

Got my parts from Bay Area Amusements.

I Love Parts

Monday, October 30th, 2006

Ordered a new ball trough from Marco Specialties.

From Bay Area Amusements I ordered a bunch of stuff:

For Medieval Madness:

  • Replacement flippers

For Shadow:

  • Replacement springs for the divertor mechanisms. Williams part #10-320.

Shadow Repairs Finished

Saturday, October 28th, 2006

Shadow is all back together and works super-awesome (er, except for the upper half of the backbox G.I. lights, which I still need to fix). The sanctum lock works flawlessly. Yay!

Backbox Decals Arrive

Wednesday, October 25th, 2006

The backbox decals I ordered from The Pinball Heaven arrived via Royal Mail, via my local USPS mailman.

I peeked inside the tube to make sure they were there and then put them away for safekeeping. Don’t feel like replacing them right now.

Sanctum Photos

Wednesday, October 25th, 2006

Here are some photos of the repaired sanctum with the surrounding parts back in place. Not bad I think.

dscn0986.jpg

dscn0983.jpg

dscn0979.jpg

Here are the closest before and after shots:

dscn0796.jpg

dscn0965_2.jpg

I’d say the lettering is a little thick and the ‘U’ is too narrow and the ‘M’ too wide. But I’m not complaining.

Reassembly Continued…

Wednesday, October 25th, 2006

Almost finished with the reassembly. Replaced the left-hand ramp with a reproduction that I ordered from Bay Area Amusements a few years ago. The old one had a metal strap on the left that broke:

Old left ramp with broken bit.

It doesn’t look like much, but it totally screwed up the way the ball exited the ramp.

As I was putting stuff together, I noticed two spots where I think there might have been Mongol figures. One above the upper-right flipper, and another to the left of the left ramp. Each spot features two perfectly placed hex screws just sitting there doing nothing.

dscn0977.jpg

dscn0976.jpg

I wonder if they were separated from my machine sometime in its past by a previous owner. Must investigate.

Another oddity… After putting in the new plastics I had two extra pieces that didn’t match anything on the playfield. They seemed to fit perfectly over each ramp though. Here they are placed over where they seem to fit. Note the right-hand ramp piece is green because it still has the protective sheeting on it.

dscn0973.jpg

dscn0974.jpg

Again, must investigate.

Parts

Wednesday, October 25th, 2006

Ordered a bunch of stuff from Bay Area Amusements:

Reassembley Started

Saturday, October 21st, 2006

Started to put everything back onto the playfield. The new plastics are absolutely beautiful and worth every penny. I took pictures of the old and new side by side but they sucked and you really couldn’t see how awesome the new plastics are.

Applying Mylar…

Friday, October 20th, 2006

Cut out two pieces of mylar from the sheet I ordered from Marco Specialties. One to fit over the little bit of playfield laminate I ripped up with masking tape, and one to fit over the entire sanctum area. I cut the sanctum piece pretty generously so that it overlapped the holes for the optos and lightbulbs, then used a hobby knife to trim out the holes.

dscn0965.jpg

The quality of the mylar from Marco Specialities is not as good as I had hoped it would be. If you look at it closely or from directly above, you can see tons of tiny gaps beetween the playfield and the mylar adhesive. Hard to see in the photo above, but if you look closely at the lettering you can see it. Rubbing it down helped a little, but it doesn’t look nearly as good as factory applied mylar.